Absolute Maximum, Thermal & Pin Cautions

Check your design against the limits the datasheet states.

Extracts absolute maximum ratings, thermal limits and resistance, and pin cautions from a datasheet, each with a source page where one was recorded. Stress limits stay apart from operating conditions, and a design value can be checked against the pin-cautions rules through the API.

TI LM1117 (SOT-223)

Real run · SNOS412Q page 4

REVIEW REQUIRED
Input voltage (VIN to GND)AMR: 20 V MAX
Recommended: 15 V maxpage 4
Junction temperature (TJ)AMR: 150 °C MAX

Recommended junction range: 0 to 125 °C for the LM1117 and −40 to 125 °C for the LM1117I.

RθJA, SOT-223 (DCY)61.6 °C/W
Soldered directly into a PCBpage 4
Max power at 125 °C ambient0.406 W

Computed by code as (TJ limit − TA) / RθJA from the extracted values, with the 150 °C absolute-maximum TJ as the limit. Verify board and test conditions before design use.

Not for design calculation without reviewMachine-use flag
Stress-Only
Limits tagged as damage boundaries
TJ = TA + PD · θJA
Computed from extracted values
Rule Check API
One design value against the rulebook
Source Pages
Attached where recorded

Try The Arithmetic

Check A Value Against A Stated Limit

These four calculators run in your browser on numbers printed in real datasheets (the TI LM1117 and the ATmega328P). They show the arithmetic the limits imply. They are illustrations. The product's own checks run on the data extracted from your datasheet.

Stress Limit vs Operating Range

Absolute Maximum Is Not A Design Limit

The LM1117 datasheet gives 20 V as the absolute maximum on VIN and 15 V as the recommended maximum. A rating is a damage boundary, so a value between the two is outside the recommended range even though it is below the stress limit.

Input Voltage (VIN to GND):12.0 V
WITHIN THE RECOMMENDED RANGE

12.0 V against a recommended maximum of 15 V and an absolute maximum of 20 V. This compares one number. Other limits in the datasheet still apply.

VIN against the two limitsLM1117, page 4
VIN (V)Rec. 15 VAbs. max 20 V12.0 V
Source: absolute maximum ratings and recommended operating conditions

Who It Is For

Useful To Every Stakeholder

Limits and cautions are cheapest to check during schematic capture and most expensive to diagnose on a prototype bench.

For Hardware Engineers

Check input voltage, current budgets and junction temperature against the limits the datasheet states, each with its source page where one was recorded.

Stress limits kept apart from operating limits

For Firmware Engineers

Find the reset, boot and pull-up cautions a datasheet keeps in footnotes and programming sections, each with a severity, a lifecycle phase and a source snippet.

Cautions with their source pages

For Engineering Directors

Get JSON records with warnings and review flags in place of a spreadsheet checklist. Each module says whether a person should review it before the data is used.

Review flags, not blind trust

Real Output Files

Machine-Readable Limits And Cautions

Each module returns a JSON contract with source pages, review flags and an audit record. These files are abridged from real runs: the LM1117 for thermal, and the ATmega328P for the rest.

// Abridged from a real run on the ATmega328P datasheet. Omissions are marked with …
// 3 of 27 ratings shown.
{
  "contract_version": "absolute_max_canonical_v2",
  "module_id": "absolute_max",
  "contract_kind": "canonical",
  "schema_version": "absolute_max_v2",
  "ratings": [
    {
      "category": "supply_voltage",
      "severity": "critical",
      "parameter": "Maximum operating voltage",
      "min_value": null,
      "max_value": 6,
      "unit": "V",
      "design_use": "stress_only_not_for_operation",
      "evidence": {
        "source_page": 258,
        "source_table_title": "28.1 Absolute Maximum Ratings",
        "source_text_snippet": "Maximum operating voltage 6.0 V"
      },
      "confidence_score": null,
      "review_required": false
    },
    {
      "category": "io_current",
      "severity": "high",
      "parameter": "DC current per I/O pin",
      "min_value": null,
      "max_value": 40,
      "unit": "mA",
      "design_use": "stress_only_not_for_operation",
      "evidence": {
        "source_page": 258,
        "source_table_title": "28.1 Absolute Maximum Ratings",
        "source_text_snippet": "DC current per I/O pin 40.0 mA"
      },
      "confidence_score": null,
      "review_required": false
    },
    {
      "category": "aggregate_current",
      "severity": "critical",
      "parameter": "DC current VCC and GND pins",
      "min_value": null,
      "max_value": 200,
      "unit": "mA",
      "design_use": "stress_only_not_for_operation",
      "evidence": {
        "source_page": 258,
        "source_table_title": "28.1 Absolute Maximum Ratings",
        "source_text_snippet": "DC current VCC and GND pins 200.0 mA"
      },
      "confidence_score": null,
      "review_required": false
    }
    …
  ],
  "recommended_operating_boundaries": [],
  "esd_ratings": {},
  "audit_summary": {
    "rating_count": 27,
    "source_backed_count": 13,
    "stress_only_count": 13,
    "review_required_count": 14,
    "unknown_category_count": 14
  }
}

Engineering Truth Standard

Built For Review, Not Blind Trust

We say where extraction saves you time and where a person still has to check. A model reads the datasheet. Code does the arithmetic and writes the audit.

What Compliance Guard Does

  • Reads absolute maximum ratings from the datasheet's tables and keeps them apart from recommended operating conditions.
  • Reads thermal resistance and temperature limits, then computes maximum power from the extracted values.
  • Reads pin cautions with a severity and lifecycle phase, and checks one design value against them through the API.
  • Attaches a source page and snippet wherever the extraction recorded them.

What It Does Not Claim

  • Static checks do not replace bench bring-up or lab qualification.
  • It does not guess errata notes or silicon revisions the datasheet does not list.
  • It flags rows it could not ground or attribute for review, and reports how many rules it could not check. In the rules/check sample above, 41 of 56 were not checkable.
  • Extracted values can contain errors, so confirm each limit on its source page before you design to it.

Free To Try

Read the limits your next IC actually states

Upload a component datasheet and extract its thermal data and pin cautions on the free passes: a new account gets five, and each runs up to two modules. Absolute maximum ratings run on module credits.

Cookies. Strictly necessary cookies keep you signed in and remember this choice. Optional analytics (Google, Microsoft, PostHog) show us how the site is used. Cookie details